A BEGINNER'S GUIDE TO INSTALLING A BATHTUB

A Beginner's Guide to Installing a Bathtub

A Beginner's Guide to Installing a Bathtub

Blog Article

Click Here

Just how do you feel when it comes to How to Install a Bathtub Yourself?


How to Install a Bathtub
Installing a bathtub isn't specifically brain surgery, however it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is likewise a moderately challenging task. If the old bathtub is conveniently available, the job can move speedily; if you have to open up a wall surface to get rid of the old tub as well as place the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need a helper to vacate the old bathtub and also embeded in the new one. Make sure you have qualified on your own for the job and are comfortable attempting it. As opposed to employing a service provider to take control of a halfway-completed job, it is better to take into consideration using one prior to you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will certainly assist you install a new tub in your shower room if you have actually already acquired a brand-new bathtub and don't require to transform the setup of your previous water supply pipelines.
Your tools and material checklist ought to make up the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installment


    First of all, the sustaining framework supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps device to avoid pressure on the bath tub.
    Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final position.

    Removing Old Touches


    If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of getting rid of the existing taps can be fairly bothersome as a result of the limited gain access to that is typically the case.
    Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
    Prior to going on to fit the new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

    Installing the Bathtub


    Using the two wooden boards under its feet, place the tub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
    The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub till the level reviews level.
    To install faucets, fit the bottom of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression join; after that do the exact same for the other tap.
    Switch on the water supply and also check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Load the bath tub as well as additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
    Ultimately, repair the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the tub must wait until the tub has actually been utilized at least once as this will certainly resolve it right into its last placement.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the existent supply pipes.
    If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Protect the faucet in position with the maker supplied backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The former type must be connected to the tap ends first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a stiff seal, triggering the water to pass through the wall in between the bath and also the tiling, resulting in complications with moisture and possible leaks to the ceiling listed below.
    You can choose from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealant can crack fairly early if you do not take into consideration this motion prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or waterproof glue as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Do you appreciate reading up on How to Install a Bathtub Yourself? Give feedback directly below. We will be delighted to find out your feelings about this write-up. We hope that you visit us again before long. Enjoyed reading our post? Please share it. Let others discover it. Thanks a lot for taking the time to read it.


    Ensure plumbing integrity; reach out.

    Report this page